Jotun SeaForce 30 Anti-Fouling Paint

Mô tả

Product description

Nội dung bài viêt!

Jotun SeaForce 30 Anti-Fouling Paint is one component acrylic, hydrosing antifouling coating based on ion exchange technology. It provides good fouling protection. This is achieved through self polishing characteristics reducing hull deterioration. To be used as finish coat in immersed environments only. Suitable on approved primers and tie coats on aluminium and carbon steel substrates. It can be applied at sub zero surface temperatures.

Typical use of Jotun SeaForce 30 Anti-Fouling Paint

Marine :

Remembered for under water hull in newbuilding and drydocking. Designed for vessels trading at a wide range of speed and activity. The product can be used for long service periods up to 60 months as a part of complete coating system.

Protective :

Can be used for offshore constructions and outside hull for static installations in deep sea.

Typical trade of Jotun SeaForce 30 Anti-Fouling Paint

Suited for vessels operating in global service, including fresh water exposure during newbuilding outfitting. Recommended for deep sea trade.

Approvals and certificates

Complaint with IMO Antifouling System Covention AFS/CONF/26.

Additional certificates and approvals may be available on request.

Colours

Dark red, light, black, blue.

Product data

Property Test/Standard Description

Solids by volume ISO 3233 58 ± 2 %

Flash point ISO 3679 Method 1 25^oC

Density calculated 1.6 kg/l

VOC-US/Hong Kong US EPA method 24 (tested) 384 g/l

(CARB(SCM)2007, SCAQMD rule 1113, Hong Kong)

VOC-EU IED (2010/75/EU) (theoretical) 399 g/l

VOC-China GB/T 23985 – 2009 (ISO 11890-1)(tested) 396 g/l

VOC-Korea Korea Clean Air Conservation Act (tested) 421 g/l

This provided data is typical for factory produced products, subject to slight varitation depending on colour.

Film thickness per coat

Typical recommended specification range

Dry film thickness 75 – 175 µm

Wet film thickness 130 – 300 µm

Theoretical spreading rate 7.7 – 3.3 m²/l

Surface preparation

To secure lasting adhension to the subsequent product all surfaces shall be clean, dry and free from any contamination.

Substrate surfaces : Coated surfaces

Surface preparation:

Minium :

+ New tie coat or new antifouling : Remove any contamination that could interfere with the intercoat adhension. Exceeding maximum recoat intervals will require cleaning/abrading and/or application of additional coats, dependent on condition.

+ Aged antifouling with leached layer : Removal by thorough fresh water washing at minimum nozzle pressure 200 bar.

Recommended

+ Aged antifouling with leached layer : Removal by thorough fresh water washing at minimum nozzle pressure 340 bar.

Application

Application methods

The product can be applied by

Spray : Use airless spray.

Brush : May be used. Care must be taken to achieved the specified dry film thickness

Roller : May be used. Care must be taken to achieved the specified dry film thickness

Product mixing

Single pack

Thinner/Cleaning solvent

Thinner : Jotun Thinner No.7.

Guide data for airless spray

Nozzle tip (inch/1000) : 21 – 31

Presure at nozzle (minimum) : 150 bar/2100 psi.

Dry and curing time

Substrate temperature -10^oC 0^oC 5^oC 10^oC 23^oC 40^oC

Surface (touch) dry 5h 2h 1h 45min 30min 30min

Dry to over coat, minimum 48h 36h 12h 9h 7h 6h

Dried/cured for immersion 48h 36h 12h 12h 10h 8h

For maximum overcoating intervals, refer to the Application Guide (AG) for this product.

When three or more antifouling coats are applied in rapid succession it is recommended to double the time for immersion.

Drying and curing times are determined under controlled temperatures and relative humidity below 85%, and at average of the DTF range for the product.

Surface (touch) dry : The state of drying when slight pressure with a finger does not leave an imprint or reveal tackiness.

Dry to over coat, minimum : The recommended shortest time before the next coat can be applied.

Dried/cured for immersion : Minimum time before the coating can be permanently immesed in sea water.

Recommended type of primer

Anticorrosive primer system suitable for purpose. Recommended tie coat for subsequent antifouling coat is : Safeguard Universal ES or Safeguard Plus.

Packing (typical)

Seaforce 30

Volume (litres) : 20

Size of containers (litres) : 20

The volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations.

Storage

The product must be stored in accordance with national regulations. Keep the container in a dry, cool, well ventilated space and away from sources of heat ignition. Containers must be kept tightly closed. Handle with care.

Shelf life at 23^oC

Seaforce 30 : 18 month(s)

For other colour than red, the shelf life is 6 months.

In som markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf life, thereafter the paint quality is subject to re-inspection.

Caution

This product is for professional use only. The applicators and operators shall be trained, experienced and have the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun’s technical documentation. Applicators and operators shall use appropriate personal protection equipment when using this product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing the work.

Health and safety

Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do not inhale spray mist.Avoid skin contact.Spillage on the skin should immediately be removed with suitable cleaser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.

Colour variation

When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.

Disclaimer

The information in this document is given to the best of Jotun’s knowledge, based on laboratory testing and practical experience. Jotun’s products are considered as semi-finished goods and as such, products are often used under conditions beyond Jotun’s control.Jotun cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements.Jotun reserves the right to change the given data without further notice.

Users should always consult Jotun for specific guidance on the general suitability of this product for their needs and specific applicaton practices

If there is any inconsistency between different language issues of this document, the English (United Kingdom) version will prevail.

KIM LOAN CONSTRUCTION TRADING SERVICE CO.,LTD

we specialize in manufacturing, distributing and applying epoxy paints

Address: No 147, street 28, ward 6, GoVap district, Ho Chi Minh City

Email : info@sonnuockimloan.com

Hotline : 028.22007114 – 028.22009114