- 1 Product description
- 1.1 Typical use of Epoxy Jotun Coastal EP Finish Paint
- 1.2 Product data of Epoxy Jotun Coastal EP Finish Paint
- 1.3 Film thickness per coat
- 1.4 Surface preparation
- 1.5 Application
Epoxy Jotun Coastal EP Finish Paint is a two component polyamide cured epoxy coating. To be used as topcoat in atmospheric environments.
Typical use of Epoxy Jotun Coastal EP Finish Paint
Recommended as a finishing coat in epoxy systems.
According to colour card and Multicolor Industry tinting system (MCI).
Product data of Epoxy Jotun Coastal EP Finish Paint
Property Test/Standard Description
Solids by volume ISO 3233 50 ± 2 %
Gloss level (GU 60O) ISO 2813 gloss (70-85)
Flash point ISO 3679 Method 1 25oC
Density calculated 1.3 kg/l
VOC-EU IED (2010/75/EU) (theoretical) 436 g/l
The provided data is typical for factory produced products, subject to slight varitation depending on colour. All data is valid for mixed paint.
Gloss description : According ti Jotun Performance Coatings’ definition.
Film thickness per coat
Typical recommended specification range
Dry film thickness 40 – 60 µm
Wet film thickness 80 – 120 µm
Theoretical spreading rate 12.5 – 8.3 m2/l
To secure lasting adhesion to the subsequent product all surfaces shall be clean, dry and free from any contamination.
Surface preparation summary
Substrate : Coated surfaces.
Minimum : Clean, dry and undamaged compatible coating (ISO 12944-4 6.1.4)
Recommended : Clean, dry and undamaged compatible coating (ISO 12944-4 6.1.4)
The product can be applied by
Spray : Use air spray or airless spray .
Brush : Recommended for stripe coating and small areas. Care must be taken to achieve the specified dry film thickness.
Roller : May be used. Care must be taken to achieve the specified dry film thickness.
Coastal EP Finish Comp A 4 part(s)
Coastal EP Finish Comp B 1 part (s)
Thinner : Jotun Thinner No.7
Guiding data for airless spray
Nozzle tip (inch/1000): 13-19
Pressure at nozzle (minimum) : 150 bar/2100 psi
Dry and curing time
Substrate temperature 10 oC 23 oC 40 oC
Surface (touch) dry 2.5h 1.5h 30min
Walk-on-dry 14h 6.5h 3h
Dry to over coat, minimum 14h 7h 3h
Dried/cured for service 14d 7d 3d
For maximum overcoating intervals, refer to the Application Guide(AG) for this product.
Drying and curing times are determined under controlled temperatures and relative humidity below 85%, and at average of the DFT range of the product.
Surface (touch) dry : The state of drying when slight pressure with a finger does not leave an imprint or reveal tackiness.
Walk-on-dry : Minimum time before the coating can tolerate normal foot traffic without permanent marks, imprints or other physical damage.
Dry to over coat, minimum : The recommended shortest time allowed before the next coat can be applied.
Dried/cured for service: Minimum time before the coating can be permanently exposed to the intended environment/medium.
Induction time and pot life
Paint temperature 23oC
Pot life 8h
Temperature continuous peak
Dry, atmospheric 120oC 140oC
Peak temperature duration max.1 hour.
The temperatures listed relate to retention of protection properties. Aesthetic properties may suffer at these temperatures.
Depending on the actual exposure of the coating system, various primers and top coats can be used in combination with this product. Some examples are shown below. Contact Jotun for specific system recommendation.
Previous coat: epoxy, epoxy mastic, inorganic zinc silicate shop primer.
Volume (litres) Size of containers(litres)
Coastal EP Finish Comp A 4 5
Coastal EP Finish Comp B 1 1
Volume stated is for factory made colours. Note that local variants in pack size and filled volumes can vary due to local regulations.
The product must be stored in accordance with national regulations. Keep the container in a dry, cool, well ventilated space and away from sources of heat ignition. Containers must be kept tightly closed. Handle with care.
Shelf life at 23oC
Coastal EP Finish Comp A 24 month (s)
Coastal EP Finish Comp B 48 month (s)
In some markets commercial shelf life can be dictated shorter by local legislation. The above is minimum shelf life, thereafter the paint quality is subject to re-inspection.
This product is for professional use only. The applicators and operators shall be trained, experienced and have the capability and equipment to mix/stir and apply the coatings correctly and according to Jotun’s technical documentation. Applicators and operators shall use appropriate personal protection equipment when using this product. This guideline is given based on the current knowledge of the product. Any suggested deviation to suit the site conditions shall be forwarded to the responsible Jotun representative for approval before commencing the work.
Health and safety
Please observe the precautionary notices displayed on the container. Use under well ventilated conditions. Do not inhale spray mist.Avoid skin contact.Spillage on the skin should immediately be removed with suitable cleaser, soap and water. Eyes should be well flushed with water and medical attention sought immediately.
When applicable, products primarily meant for use as primers or antifoulings may have slight colour variations from batch to batch. Such products may fade and chalk when exposed to sunlight and weathering.
The information in this document is given to the best of Jotun’s knowledge, based on laboratory testing and practical experience. Jotun’s products are considered as semi-finished goods and as such, products are often used under conditions beyond Jotun’s control.Jotun cannot guarantee anything but the quality of the product itself. Minor product variations may be implemented in order to comply with local requirements.Jotun reserves the right to change the given data without further notice.
Users should always consult Jotun for specific guidance on the general suitability of this product for their needs and specific application practices
If there is any inconsistency between different language issues of this document, the English (United Kingdom) version will prevail.
KIM LOAN CONSTRUCTION TRADING SERVICE CO.,LTD
We specialize in manufacturing, distributing and applying epoxy paints
Address : No.147, Road 28, Ward 6, Go Vap District, Ho Chi Minh City